I found this photo on my drive. I think this piece of fine furniture is a Robote by Jon Chippendale, down under (please correct me if I'm wrong).
Contents:
Contact info:
Jim Michalak
118 E Randall,
Lebanon, IL 62254Send $1 for info on 20 boats.
Jim Michalak's Boat Designs
118 E Randall, Lebanon, IL 62254
A page of boat designs and essays.
(15Apr09)This issue will rerun the Rigging Sharpie Sails issue. The next issue will take a look at rudders.
THE BOOK IS OUT!
BOATBUILDING FOR BEGINNERS (AND BEYOND)
is out now, written by me and edited by Garth Battista of Breakaway Books. You might find it at your bookstore. If not check it out at the....ON LINE CATALOG OF MY PLANS...
...which can now be found at Duckworks Magazine. You order with a shopping cart set up and pay with credit cards or by Paypal. Then Duckworks sends me an email about the order and then I send the plans right from me to you.
MESSABOUT NOTICE:
THE REND LAKE MESSABOUT WILL TAKE PLACE ON JUNE 12 and 13 AT THE PINTAIL LOOP OF THE NORTH SANDUSKY CAMP GROUND AT REND LAKE IN SOUTHERN ILLINOIS. THIS IS A CHANGE FROM PREVIOUS YEARS. I WON'T BE IN CHARGE OF THE MEET THIS YEAR. INSTEAD OUR TIRELESS FRIEND ROB ROHDE-SZUDY WILL TAKE A STAB AT IT. CONTACT HIM AT robrohdeszudy@yahoo.com FOR MORE CAMPING INFO IF YOU NEED IT .
RIGGING SHARPIE SPRIT SAILS
BACKGROUND...
My first homebuilt boat, in 1981, was a Bolger Teal rigged with a 59 square foot sharpie sprit sail. Next boat was the Bolger Jinni with a 96 square foot main and small mizzen, both sharpie sprits. Later came Birdwatcher with a 126 square foot sharpie sprit. I've used the sharpie sprit on lots of my own designs thinking it about the best sailing cheap rig (although it has its disadvantages too). In this essay I'll pass along what I think I've learned about it.
THE BASIC ELEMENTS...
Figure 1 shows the basic elements of the sharpie sprit rig. We'll talk about them one by one. The basic elements are the MAST, the SAIL, the MAST/SAIL ATTACHMENTS, the SPRIT, the SPRIT ATTACHMENTS. Here we go...
THE MAST...
The sharpie sprit mast is actually one of its main disadvantages...the mast needs to be long compared to something like the mast of a balanced lug rig. For example my 12' Teal needed a 16' mast to set enough sail to be interesting, the Jinni needed a 21' mast on its 15' hull, and the Birdwatcher needed a 24' mast on its 24' hull. In general the mast needs to be longer than the boat, sometimes by a goodly amount. That causes problems in trailering and cartopping, especially with the smaller boats. It's at its worst with a small row/sail boat like Teal. If you have to row the boat after sailing, you need to leave the rig standing. Where are you going to put a 16' mast in a 12' boat? If there is any wind about, rowing the boat with the rig standing is very difficult. On Jinni I put a set of crutches fore and aft to stow the rig. The crutches were off centerline so I could launch and row the boat with the rig still stowed - very important. Never stow such a rig on centerline if you don't have to. Actually the mast length problem would be no different for any triangular sail rig.
As for mast material, low tech wood is the way to go. I've tried aluminum and other pieced together solutions and I'll report on them some issue. But the single straight stick seems to be the best. The three boats I mention all had masts with square cross sections (even though the Birdwatcher was supposed to be octagonal). The square masts are a lot easier to build than the octagonal or round masts. I suspect they work about as well. They are stiffer for the size and can easily be built hollow like a box if you want, although if you crank through the numbers you might find that a hollow mast in the size we are talking about saves very little weight. But I don't think a mast should ever be made of a single piece of wood, at least not the wood my sources carry. Always laminate from at least two layers to minimize warping.
Sharpie sprit masts are usually unstayed, that is they have no supporting guy wires. That means a heavier mast but a simple and easily assembled structure. I think a stayed mast would work as long as you were on the lookout for interference between the wires and the sprit as it projects forward.
I might add that from a practical standpoint the 24' Birdwatcher mast, which weighs perhaps 35 pounds, is about all one man can put up by himself with repeatable ease. Even then you must use care, practice and patience and be in control of the thing all the time. You must really rig the boat on shore. The small skiffs often don't have the stability needed to allow you to stand up in the boat trying to balance a 16' stick on end. In rough water it is not possible without good luck. And with the larger ones you may have the stability to try to raise the mast while afloat but any passing wave that rocks the boat as you stand a 24' mast on end will invite disaster.
THE SAIL...
Up until a month ago all the sharpie sprit sails I had made were of real Dacron sailcloth using instructions from SailRite books. As far as I'm concerned they all went quite well. The SailRite books contain all the information you need although the book I used, written 20 years ago, was a bit jumbled. But since then I think I've learned a few things needed to tweak the general instructions to sharpie spritdom.
For one thing, almost any sharpie sprit sail will benefit from having its leech (trailing edge) hollowed out. If you don't do that the leech will flutter with a loud motor boat sound in higher winds. Usually 2 or 3" on a 20' leech might be enough. I don't think there is any special number, but you do have to hollow it out.
Next, the foot of the sail should be cut more or less as if the sail had a boom which is to say with some "round". I've always use the SailRite instructions for getting the round. I've seen Phil Bolger write that the foot should be cut straight. But I can't see that if you are looking for shaping in some camber. My feeling is that the tension in the foot of these sails is so high that the foot is going to straighten out due to the load no matter how you shape it, so it ends up as if you had laced it to a straight boom.
Next, the luff of the sail needs a lot of "round" mostly to allow for the backward bend of the unstayed mast, which can be considerable. Here again SailRite gives good guidance in suggesting the mast be supported at it ends, a weight equal to half the sail area suspended in the middle, and the resulting deflection "mapped" and applied to the luff. The "round" needed to allow for sail draft shaping is added to the deflection round but it is usually a lot smaller than the deflection round. You might be surprized how much round the luff may need - a 14' luff may need 5" or 6" of round, especially if the mast is limber!
As for allowance for draft, I think a camber of 7% to 10% is fine. I recall somewhere that Marchaj, who wrote the book on scientific testing of this sort, said there is no reason to ever give a sail more than 10% camber by any testing he has seen.
Lastly, I've been experimenting with a small polytarp sharpie sprit sail recently and should have a full report with "how to" within a few months.
MAST/SAIL ATTACHMENTS...
This is where the sharpie sprit sail starts to get interesting. Because the sprit must be attached to the mast well above the foot of the sail, the sharpie sprits of old could not use a regular halyard. If they did so, the sprit attachment would interfere with the normal sail attachments of the time - hoops or lacing. As the sail is lowered with the halyard, the hoops or lacings needed to pass over the sprit attachment and there is no simple way to do that. So traditional sharpie sprits had no halyards! The sail is tied to the mast head forever. You can never raise and lower sail in the usual way.
Once you accept that you have no halyard, some economies become apparent. Not only are the halyard and block eliminated, but the mast compression that results in the downward pull of the halyard is gone (as it is in high tech rigs where the halyard is secured over a stop at the top of the mast as with a Hobie cat). And the mast can be thinner up top for that. I think the top of the Birdwatcher mast, 24' long overall, is no more than 1" square.
Not needing a halyard allows for a very simple sail/mast connection, indeed. Bolger likes best simple ties every 18" or so around the mast. If one tie fails it is of little consequence. This is what the Birdwatcher used. The sail stays tied to the mast at all times. Bolger suggested a way to furl and stow such a rig.
Here is a photo of my Birdwatcher with mast and sail furled. The sprit has been stowed, the sail rolled up like a sausage and the roll secured to the mast with a bungee. (On a small boat you can actually roll the sprit up inside the furl.) Looks great and simple doesn't it.
There were two problems with this method of stowing. One is that wind can get into the roll high above the tie and unroll the sail making for uncontrolled thrashing and noise and danger. It can undo you with its violence if you try to furl the rig say at the approach of a thunderstorm which later produces very strong wings. I found a nice easy solution. I tied a light line to the masthead which led down the side of the mast to a cleat near the deck. After I had the sail rolled up I would uncleat that light line and wrap it around the sail/mast working from the deck and spiraling the line around and around. Tug hard and recleat the line and the sail was secured from tip to toe. And that is how the rig was stowed for trailering too. Never came loose.
But I never solved the second problem with this furl. A sail rolled like this will eventually take a permanent curl at its trailing edge. It can't be good for the sail shape. The only thing I could think of to solve this was to roll the sail a different way each time.
Simple lacing works well too. There are lots of lacing schemes but here are two I tried with Jinni and both worked well. Actually these lacings can work with a halyard given some tricks which we'll look into next time.
I found the masthead lacing to be a special challange. The sail needs to be pulled up at the masthead and also pulled close to the mast. With simple ties, two separate ties will do the job. But with lacing you need to try to give a special extra loop around the mast at the top grommet so that the lacing pulls both up and into the mast. Be ready to tinker.
After I had tried all of the above with Jinni I went to the method the plans called for - standard sail track. I found an oldster in selling 20' of sailtrack for $20 in Messing About In Boats classifieds and scooped it up because now the stuff costs $5 a foot if you can find it at all. It worked perfectly, better than all the lacing schemes. But if I had to pay retail for the track, I would go back to lacing. I think in many ways that the old traditional ways of rigging boats are coming back because the materials, like sailtrack and Dacron sailcloth which made the traditional ways obsolete, are now getting too expensive to consider.
As for the tack attachment, like the masthead attachment it is best done with two separate lines, one around the mast to hold the sail close to the mast, and another pulling down on the sail. The one that pulls down is best done this way: Have a line tied through the base of a cleat near the bottom of the mast. Run the line up through the tack grommet and back to the cleat where you belay it. This way you will have a two-to-one advantage here (ignoring friction) and can really crank in some luff tension if you need it. If you see the luff of your sail starting to pucker between its luff grommets in higher winds, you can remove the puckers with more tension on the tack attachment. This way is a lot easier that trying to retension any halyard, if you have a halyard. In fact it might be worth setting the tack line to a spring loaded cam cleat instead of a regular cleat to allow for instant adjustments. Like this:
THE SPRIT...
In a lot of ways the sprit makes the rig into a bow-and -arrow affair and makes the sharpie sprit a high performer. The sprit itself is in compression and can usually be fairly light. I used a 1-1/2" square sprit for Jinni's 96 square foot main and a tapered 1-1/2" x 3-1/2" sprit for Birdwatcher's 16' sprit.
The sprit itself sort of floats free with its aft end tied to the sail's clew, and usually attached to the sheet there. The fore end is attached to the mast with a tackle called a "snotter" More on that later.
But if you put tension in the snotter you put compression in the sprit which forces the clew aft. That tensions the foot and leech which in turn pulls the masthead aft. Here is what happens.:
By varying the tension in the snotter you can preload the mast bend to what you want and that varys the draft of the sail to something you want. It's actually quite adjustable although there are limits to it all. So this very simple rig can do things for which other boats need adjustable stays, etc. I always found the thing works very well. I have a feeling that, as with most "preloaded structures", the preloaded bendy mast retains the shape that you put into it until the wind force overcomes the preload. So the sail shape will stay constant until that wind force is attained, the sail shape does not change with the wind below that threshold. So I've always felt that the rig should almost always be preloaded to some degree. I never bought into the idea that one should set the snotter tension light for light winds and high for high winds. I kept the snotter tension high all the time and hoped for a constant sail draft and shape.
One major point about the sprit geometry is how high up the mast the snotter attachment should be. The higher up you go the greater the tension in the leech and foot and the more rigid in general the arrangement. I should mention now that another advantage of the sharpie sprit is that it is "self vanging" which is to say the clew does not lift up as sheet tension varies as with a normal sail. With a regular boomed sail, the sheet pulls downward on the sail and boom to resist the upward pull of the leech. When the boom is swung forward as when running downwind, the sheet usually no longer pulls downward and the boom usually lifts up. That allows the leech to go slack, the sail looses its shape and sometimes its control. So often regular boomed sails have a vang that runs from boom downward and forward to the mast to eliminate the lifting of the boom. The sharpie sprit doesn't need a vang because the sprit is always pushing the clew down. The greater the angle between the sprit and foot, the greater the affect. So sometimes you might see the snotter tackle attached up quite high to take full advantage. I suppose the optimum would be when the sprit sort of bisects the angle formed by the leech and foot.
But it can be overdone from a practical standpoint and here is why. On both Jinni and Birdwatcher I've had the snotter attachment break or rattle loose while underway. It only happens in bad conditions, course. You need to repair it quickly because you won't have control of anything until you do. If the snotter attachment is more than chest high, you will be in danger at repairing it. Having to stand on a deck to effect the snotter attachment is a total no no as far as I'm concerned. You won't be able to do it in the bad conditions that caused the failure to start with. So that's why I place my snotter tackles somewhat lower than some other designers and builders.
SPRIT ATTACHMENTS...
One thing to keep in mind about the sprit is that it sometimes must be rigged very quickly. Another thing to keep in mind is that if it comes loose you loose everything!
Here is how I like to connect the sheet and sail to the sprit's aft end. A simple open based cleat is attached to the sprit there. The sheet has a stopper knot about two feet from its end and is led through the base of the cleat until the stopper knot bears against the cleat, then through the sail's clew grommet, and the belayed back on the cleat. Be sure there is enough rope beyond the stopper knot to do all of this quickly. Variations on this are that on smaller boats it can be nice to leave the sheet permanent to the sprit, in which case a second stopper knot can be tied in above the cleat, capturing it. Another variation is to have a snap hook tied in to the end of the sheet so that instead of having to belay the sheet after looping it through the clew, you simply snap the hook into the clew.
Here is how I like to connect the snotter tackle. In my opinion all snotter tackles should be at least 2:1 to allow power to easily preload the mast. So a small sail, say less that 100 square feet, should have something like in Figure A. Again an open based cleat is attached to the fore end of the sprit. A snotter line is prepared with a stopper knot and passed through the base of the cleat, around the mast and back to the cleat where it is belayed. Some sort of eyepad will be needed on the mast to keep the snotter located on the mast. For larger boats, the multi part tackle shown in Figure B is suggested. It can be put on in an instant with the snap hook. The end of the sprit is slotted to take the loop holding the block and the slot needs to be just the right width to allow a press fit of the loop rope. This is the rig I use on Birdwatcher. The snotter lead is then lead down to a belaying pin near the base of the mast.
SPORTDORY
LIGHT ROWBOAT, 15' X 4', 70 POUNDS EMPTY
SPORTDORY
Sportdory is an attempt to improve upon the Bolger/Payson dory I built about 15 years ago. This boat is slightly smaller than my old dory. In particular the bow is lower in hopes of cutting windage. the stern is mostly similar. The center cross section is about identical. This boat has slightly more rocker than the original Bolger dory.
The hull is quite simple and light, taped seam from three sheets of 1/4" plywood, totally open with no frames. The wales are doubled 3/4" x 1-1/2" pieces to avoid the wale flexing my first boat had. I've added an aft brace to stiffen it up and give the passenger a back rest.
Mine once covered 16 statue miles in four hours. In rough water you will feel the waves are about to come on board but they won't. But if you try to stand up in one it will throw you out with no prayer of reentry.
The prototype was built by John Bell of Kennesaw, Georgia. Here is a photo of John's Sportdory under construction. You can see the sides and bottom, precut to shapes shown on the plans, wrapped around temporary forms and "stitched" together with nylon wire ties in this case. I'm quite certain that with this design one must leave the forms in place until all the structural elements like the wales and cross bracing have been permanently installed. If they are removed before then, the assembly will change shape and you won't get the same boat. In particular I think the nose will droop to no one's benefit.
One might wonder about a comparison of Sportdory, Roar2 and QT. They are all about the same size and weight, a size and weight I've found ideal for the normal guy. They are small enough to be manhandled solo yet large enough to float two adults if needed. They are all light and well shaped for solo cartopping. Roar2 is probably the most involved to build and the best all around of the three. Sportdory is simpler and lighter, at least as fast and as seaworthy, but most likely will feel a little more tippy and less secure. You shouldn't really try standing up in either of these two. QT will be the least able of the three as far as speed and seaworthiness but may be the easiest and cheapest of the three and is stable enough to stand up in. So take your pick.
Sportdory plans are $20.
Prototype News
Some of you may know that in addition to the one buck catalog which now contains 20 "done" boats, I offer another catalog of 20 unbuilt prototypes. The buck catalog has on its last page a list and brief description of the boats currently in the Catalog of Prototypes. That catalog also contains some articles that I wrote for Messing About In Boats and Boatbuilder magazines. The Catalog of Prototypes costs $3. The both together amount to 50 pages for $4, an offer you may have seen in Woodenboat ads. Payment must be in US funds. The banks here won't accept anything else. (I've got a little stash of foreign currency that I can admire but not spend.) I'm way too small for credit cards.
I think David Hahn's Out West Picara is the winner of the Picara race. Shown here on its first sail except there was no wind. Hopefully more later. (Not sure if a polytarp sail is suitable for a boat this heavy.
Here is a Musicbox2 I heard about through the grapevine.
This is Ted Arkey's Jukebox2 down in Sydney. Shown with the "ketchooner" rig, featuring his own polytarp sails, that is shown on the plans. Should have a sailing report soon.
And the Vole in New York is Garth Batista's of www.breakawaybooks.com, printer of my book and Max's book and many other fine sports books. Boat is done, shown here off Cape Cod with mothership Cormorant in background, Garth's girls are one year older. Beautiful job! I think Garth is using a small lug rig for sail, not the sharpie sprit sail shown on the plans, so I will continue to carry the design as a prototype boat.
And a new Down Under Blobster, now rightside up for final finish. Looks like another beautiful job....
A view of the Caroline prototype showing a lot of the inside, crew on fore deck. Beautiful color:
I gotta tell you that on the Caroline bilge panels I made an error in layout and they are about 1" too narrow in places on the prototype plans. I have them corrected but it always pays, even with a proven design, to cut those oversized and check for fit before final cutting.
And a Family Skiff is going together in mid Missouri...
AN INDEX OF PAST ISSUES
Hullforms Download (archived copy)
Plyboats Demo Download (archived copy)
Brokeboats (archived copy)
Brian builds Roar2 (archived copy)
Herb builds AF3 (archived copy)
Herb builds RB42 (archived copy)